Wanted: Used Banjo axle
front drive flanges
Contact bmuller@vehiclesofvictory.com
2008
Wanting
mounting bracket for the BO light that mounts high
on the brush guard on a 1942 G506. Could use the BO light too. Also
need the gas tank filler neck.
email
Billy:
sass4130@aol.com Posted
6/5/08
Looking for M211 axles
or axles shafts 27 spline.
Please contact Duane at
posterchild37@comcast.net
Posted 7/28/08
Looking to purchase and restore a
Chevrolet G506 1.5 ton. Looking for a complete unit in very good
condition. I live near Vancouver Canada and am about 10 minutes to
the Sumas WA border crossing.
WANTED.. The bracket that fits over the door hinge that the mirror arm
attaches to. Please send info as to condition, and price to
rbarber41@hotmail.com
Posted 7/21/0
|
I have a G7163 Auger truck that runs ,
needs brakes and restored. I am looking for auger parts and pieces
or I am looking for a home for the bed, winch and all parts to
convert this truck into a troop bed truck. I have lots of pictures.
I also have the lifting poles to lift from the winch that attach to
the bed. I have raised the rear of my pickup truck off the the
ground with this truck. I would like to find a good home for the
winch assembly and bed or if someone has the correct parts that I
need then give me a call so I can keep this truck stock and
historically intact. Email to
Dieselmec21@Yahoo.com
for pictures and more info. I live in Ely , Nevada.
Posted 6/26/08
|
I have had a K51
panel truck and I have a few questions for
your experts, maybe you could post them or tell me how to do?
The K52 is trailer that goes with it had PE 95 in it, gas cans,
spare tire holder, tool/cable bon in it, etc. I need pics, manual, or
whatever other info I can find. It is a Ben Hur modified as far as I
can determine.
My K51 has a window on the side and on
top, and I will try send you a picture you can post if you want. My
questions for the experts are related to the windows, are they added
by military or are they totally non-military?
By the way, my spare tire carrier was
cut off, as almost all of the panel trucks were. Sam Werner had
one, and Russ Jones has mad a great replica from Sam's pattern, in
case anybody needs one. I know these panels are scarce, I have seen
only about a dozen of them. Thanks for
your help, and keep up the great site! Al Hansel 507-528-2780
Wanted
transmission for '42 G506 on WA state or in the western 11. truck has
been sitting in the weather for over 30 to 40 yrs water got into the
tranny and most small parts have rusted away phone 509 322 1687
e-mail j509h@aol.com
posted 2/20/08
My
name is Joe and I am seeking a Chevy panel truck from 1940 -
1942, one ton or 1 1/2 ton, for use to represent the Chevy ambulances
which were gifted as war aid from the u.s. and Canada.
2007
My name
is Konstantine. I am looking for Studebaker US-6 cargo
version. Please e-mail me
kkh@acteeum.com
Posted 7/22/07“Wanted
Machine Gun Ring for
GMC 353 closed cab.
Contact Konstantine Khlyevny at
kkh@acteeum.com
Posted 7/7/07.
1942, 1.5ton
4x4 Chevy, need top bows, any seats, closed cab doors,
spare wheel carrier, ect, Can you help, Gordon
weegordi@yahoo.com.au
5/7/07
Wanted T-93
Warner Muncie 5-spd trans.
mribbich@wi.rr.com
(262) 392-2989 Posted 5/1/07
Wanted: CCKW floor pan and
firewall electrical junction box
mmitchboyd@comcast.net
Wanted GMC COE AFKWX or AFKX
Must be in running condition restoration no problem.
Wanted GMC COE 1939/1940/1941 from good to restorable condition.
I am looking for a set of
troop seats for a LWB CCKW353. Wood condition does not
matter but all metal parts must be there. Please e-mail
Scott at
od_willys@bellsouth.net or call
864-296-0136 or
864-314-5415. Would prefer that they be located in
the southeast but will consider anything
Dump Truck Parts: I'm looking for the following parts to complete the conversion
of my cargo truck to a Hercules-equipped dump truck:
PTO control levers
Bracket that mounts to inside rail of chassis to hold the PTO levers
Short PTO rod that goes from the engage lever to the PTO
Long rod that goes from the up/down lever to the pump
PTO driveshaft (front half or whole)
U-bolts to mount the dump unit to the chassis
Brackets that hold the taillights and trailer electrical plug
Contact John Zollinger email: zeemail@aol.com posted 2/8/07
